| Dimensions (H x W x D) (centrifuges): |
355 x 630 x 600 mm |
| Acoustic signal, switchable: |
yes |
| Display speed / g-force: |
speed and g-force |
| Display shows dimensions: |
yes |
| Acceleration max.: |
Rotor 11132: 20 s, Rotor 12154: 28 s |
| Linear acceleration curves: |
10 |
| Acceleration curves, quadratic: |
10 |
| Deceleration and brakeless: |
Combination from 1000 - 150 rpm selectable |
| Deceleration curves, linear: |
10 |
| Deceleration curves, quadratic: |
10 |
| Deceleration max.: |
Rotor 11132: 12 s, Rotor 12154: 53 s |
| Continous run: |
yes |
| Lid release / lid open: |
Auto lid release at the end of the run, switchable, Auto lid open, switchable |
| Display (centrifuges): |
TFT |
| Speed max.: |
18000 rpm |
| Speed min.: |
100 rpm |
| Speed increments (Centrifuges): |
10; 1 rpm |
| Calculation for liquid density: |
>1.2 g/cm3 |
| User defined acceleration curves: |
10 |
| User defined deceleration curves: |
10 |
| Brakeless: |
yes |
| User defined program name: |
yes |
| Frequency (Centrifuges): |
50/60 Hz |
| Capacity of vessels: |
0.2 ml, 0.25 ml, 0.4 ml, 0.5 ml, 1.5 ml, 2 ml, 5 ml, 7 ml, 10 ml, 15 ml, 25 ml, 30 ml, 50 ml, 85 ml |
| Noise level at max. speed: |
Rotor 11132: 60 dB (A), Rotor 12154: 66 dB (A) |
| Weight without rotor: |
78 kg |
| Height with open lid: |
785 mm |
| Capacity/capacity max.: |
4 x 400 ml |
| Kinetic energy max.: |
22989 Nm |
| Short run: |
yes |
| Cooling, heating: |
heating, cooling |
| Run monitoring: |
yes |
| Power consumption (centrifuges): |
1010 W |
| Max. radius decreaseable : |
yes |
| Microprocessor controlled: |
yes |
| Optical display stillstand: |
yes |
| Permanent display preselected, current values: |
yes |
| Programmes (centrifuges): |
60 |
| Rotors, pre programmed: |
All rotors pre programmed speed, g-force, radius |
| Rotor type: |
MTP rotor, angle rotor, swing-out rotor, PCR rotor, special rotor |
| Rotor temperature min.: |
Rotor 11132 at 5,500 rpm: less than 4 °C, Rotor 12154 at 18,000 rpm: less than 2 °C, Rotor 11132 at 5,500 rpm: < 4 °C, Rotor 12154 at 18,000 rpm: < 2 °C |
| Fast cool program: |
Rapid temp |
| G-force increments: |
10;1 xg |
| Safety (centrifuges): |
4-digit code protection, free selectable, Start refused with exceeded temperature tolerance, tolerance preselectable, Pop up window end of rotor life time |
| Signal length preselectable: |
yes |
| Voltage (centrifuges): |
220 - 240 V |
| Start delay: |
yes |
| Controller (Centrifuges): |
Control unit lockable |
| Standstill heating, switchable: |
yes, yes |
| Temperature increments: |
1 °C |
| Switchable °C, °F: |
yes |
| Time setting range: |
10 sec - 99h 59min |
| Centrifuge type: |
universal centrifuge |
| Time increments: |
60; 1 s |
| Timing after: |
set speed has been reached, switchable |
| Counting cycles: |
Counting cycles centrifuge, each rotor |
| Shipping weight: |
94,00 kg
|
| Item weight: |
79,00 kg
|
